HOW TO RESET CANON MP SERIES



MP150, MP160, MP170, MP180, MP450, MP460. MP150, MP160, MP170, MP180, MP450, MP460

If you encounter an error like "Ink absorber is full" or "Error Code 5B00" Display in your  computer while you using the printer  or an Error Code 27 display in the front panel of your printer . Its mean that the Printer Counter Protection is Full and it required a reset and Ink wastepad must be replacement or you clean the wastepad if you have no replacement, if you want your printer to work normal again. There are two ways how to troubleshoot  the Canon MP Series printer, first One we to reset manually using hardware method and second  by using a Software tool to reset permanently the EEPROM of the printer.

 Below is the procedure on how to reset your Canon MP Series printer. 

1. Download the MPTOOL.
here: http://www.4shared.com/rar/lpVUM3ij/MptoolV094.html

2. After Downloading the MPTOOL, we must manually reset first the Printer using hardware method but this method is not a permanent reset the EEPROM.

here the procedure to reset manually.


  1. Turn off the Printers.
  2. Press and Hold the button Resume/Cancel then press POWER button.
  3. Release the Resume/Cancel button while keeping POWER button on press.
  4. Press Resume/Cancel 2 times and then release all the buttons.
  5. When the indicator recorded GREEN - click Resume/Cancel 4 times!
  6. Turn off and On the Canon Pixma MP Printers. And your done.


3. After manually reset the printer using hardware method now to reset permanently the EEPRON of the printer we need to run the MPTOOL that we download earlier.

here the procedure to reset using Software.

  1. Turn off the Printers.
  2. Press and Hold the button Resume/Cancel then press POWER button.
  3. Release the Resume/Cancel button while keeping POWER button on press.
  4. Press Resume/Cancel 2 times and then release all the buttons.
  5. When the indicator recorded GREEN - Go to MP TOOL Select the model of the printer and Reset Main and Reset Plater follow the image.
  6. Turn off and On the Canon Pixma MP Series Printers. And your done you can now start to print normally.
 Using Mptool Software is very easy to use, than the other software, just follow the procedure and your done. 


thank for you viewing 


Common Canon MP Series Printer Error Messages

  • P02 (Carriage error)
  • P03 (Line feed error)
  • P05 (ASF sensor error)
  • P06 (Internal temperature error)
  • P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full.
  • P08 (Print head temperature rise error)
  • P09 (EEPROM error): – The logic board need to be replaced for this one.
  • P15 (USB VBUS over current)
  • P20 (Other hardware error
  • P22 (Scanner error)
  • E13 or E16: Ink has run out. Press the Stop / Reset button for 5 to 8 seconds until the led screen display number 1.
  • E04, E05, E14 or E15: Cartridge may not be installed properly. Reinstall the ink cartridge.
  • E2-2 = No paper (ASF)
  • E3-3 = Paper jam
  • E4 = No ink
  • E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
  • E8 = Waste ink absorber full, or platen waste ink absorber full
  • E9 = The connected digital camera / video camera does not support Camera Direct Printing
  • E14 = The Ink cartridges whose destination are wrong
  • E15 = Ink cartridge is not installed E16 – Ink remaining is unknown
  • E16-E19 = Failed to scan head alignment sheet
  • E22 = Carriage error
  • E23 = Paper feed error
  • E24 = Purge unit error
  • E25 = ASF(cam) sensor error
  • E26 = Internal temperature rise error
  • E27 = Waste ink absorber full or platen waste ink absorber full
  • E28 = Ink cartridge temperature rise error -
  • E29 = EEPROM error
  • E33 = Paper feed position error
  • E35 15 = USB Host VBUD overcurrent error – USB
  • E37 17 = Abnormal motor driver error
  • E40 20 = Other hardware error
  • E42 22 = Scanner error


How to Reset Epson tx121, tx121x and Epson me320, me340

EPSON TX121 AND TX121X


This time i will discuss how to troubleshoot Epson tx121, tx121x and     epson me320, me340 printer.
with and error code display in the computer "the waste ink tank is full"

First we need to download the  adjProg tool so we can reset the   printer.
here: http://www.4shared.com/rar/uNHjDbgN/Waste_ink_reset_Epson_ME320_ME.html

EPSON ME320 AND ME340
Note:
Be sure the your Printer Connected to your Computer and the printer switch ON.


After we download the "adjProg tool" for our  Printer.

A. Extract the "AdProg tools" that you download.
B. Run the "adjProg.exe"  
C. Then follow the steps in picture bellow.

Step1. Click Accept.























Step2. Click Select.
























Step3. Select the Model of the printer you need to reset and Click OK.

Note: If your printer epson tx121x select Epson Stylus TX121.
          If you printer Epson me 340 select Epson Stylus ME320.






















Step4. Select the ESP as a Destination then Click Ok.




















Step5. Click the Particular adjustment mode.





















Step6. Select Waste ink pad counter and Click OK.




















Step7. Check the  Main Pad Counter and alson the FL Box Counter Click Initialization.


















Step8. Click OK.

After Clicking OK we need to wait a few second and wait to Pop up the Message that require to Turn OFF the printer.

After the printer Turn Off there was a message Pop up again Click OK, Switch ON your printer and
the printer will back normal again you can now Start Printing.


THANK YOU...

How to Reset Epson t13 and Epson me32

EPSON T13
This time i will discuss how to troubleshoot Epson t13 and epson me32
with and error code display in the computer "the waste ink tank is full"

First we need to download the adjProg tool so we can reset the printer.
here: http://www.4shared.com/rar/cTaCv2k1/T13_ME32.html

Note:
Be sure that your Printer Connected to your Computer and the printer switch ON.
EPSON ME32

After we download the "adjProg tool" for our  Epson t13 and Epson me32

A. Extract the "AdProg tools" that you download.
B. Run the "adjProg.exe" 
C. Then follow the steps in picture bellow.

Step1. Click Accept.
























Step2. Click Select.























Step3. Select the Model of the printer you need to reset and Click OK.






















Step4. Select the ESP as a Destination then Click Ok.






















Step5. Click the Particular adjustment mode.






















Step6. Select Waste ink pad counter and Click OK.






















Step7. Check the  Main Pad Counter and alson the FL Box Counter Click Initialization.
















Step8. Click OK.

After Clicking OK we need to wait a few second and wait to Pop up the Message that require to Turn OFF the printer.

After the printer Turn Off there was a message Pop up again Click OK, Switch ON your printer and
the printer will back normal again you can now Start Printing.


THANK YOU...



How To Reset Canon IP2770 Printer


message indicate if the lights blink on the RESUME & button alternately and it will show an error code "5B00"& printer it means that your "Waste Ink Absorber Full".

first we need to download Service tools or a software to reset canon IP2770 printer: Here
http://www.4shared.com/rar/wrcByJ8f/Service_tool_v3400.html

After downloading the Canon Service tools
here step and How to Reset Canon IP2770 Printer error code "5B00"

1. Canon IP2770 printer should be in SERVICE MODE.
2. Turn off the Canon IP2770 Printer with power cord still attached to the position of the source of electric current.
3. Press and Hold the  STOP / RESET button.
4. Press and hold the Power button with out Releasing STOP / RESET button.
5. Release the STOP / RESET button and the power button remained Press and Hold.
6. Press the STOP / RESET 5 to 6x (5 to 6 times.) and release both buttons simultaneously.
7. If you will notice that the the Alternate Blinking error is gone, this means that the printer is in Service Mode.
9. Extract the Canon  Service tools that you download.
10. Run the canon Service tool.
11. Click Auto in menu and Unchecked all Boxes.
12. Click Main in menu be sure the Clear Ink Counter and Ink Absorber Counter is set to Main.
13. Click the Counter Value set to 0 and then Click the set button.
13. Then Turn Off the printer.
14. Turn On the printer and it back to normal again and you can now start printing.



Thank you...



How To Reset Canon MX 366 Printer


message indicate and Error Code "E07" "E08" in the control panel of the printer it means "Waste Ink Absorber Full".

first we need to download MX366 Service tools or a software to reset canon MX366 printer: Here
http://www.4shared.com/rar/wrcByJ8f/Service_tool_v3400.html

After downloading the Canon MX366 Service tools
here step and How to Reset Canon MX366 Printer error code "E07" or "E08"

1. Canon MX366 printer should be in SERVICE MODE.
2. Turn off the Canon MX366 Printer with power cord still attached to the position of the source of electric current.
3. Press and Hold the  STOP / RESET button.
4. Press and hold the Power button with out Releasing STOP / RESET button.
5. Release the STOP / RESET button and the power button remained Press and Hold.
6. Press the STOP / RESET 5 TO 6x (5 to 6 times.) and release both buttons simultaneously.
7.Then the Canon MX366 will be in service mode and LCD Panel will turn to Black
9. Extract the Canon Service tools that you download.
10. Run the canon Service tool.
11. Click Auto in menu and Unchecked all Boxes.
12. Click Main in menu be sure the Clear Ink Counter and Ink Absorber Counter is set to Main.
13. Click the Counter Value set to 0 and then Click the set button.
13. Then Turn Off the printer.
14. Turn On the printer and it back to normal again and you can now start printing.



Thank you...


How To Reset Canon MP287 Printer


message indicate and Error Code "E08" in the control panel of the printer it means "Waste Ink Absorber Full".

first we need to download MP287 Service tools or a software to reset canon MP287 printer: Here
http://www.4shared.com/rar/wrcByJ8f/Service_tool_v3400.html

After downloading the Canon MP287 Service tools
here step and How to Reset Canon MP287 Printer error code "E08"

1. Canon MP287 printer should be in SERVICE MODE.
2. Turn off the Canon MP287 Printer with power cord still attached to the position of the source of electric current.
3. Press and Hold the  STOP / RESET button.
4. Press and hold the Power button with out Releasing STOP / RESET button.
5. Release the STOP / RESET button and the power button remained Press and Hold.
6. Press the STOP / RESET 6x (6 times.) and release both buttons simultaneously.
7.Then the Canon MP287 will be in service mode.
9. Extract the Canon MP287 Service tools that you download.
10. Run the canon Service tool.
11. Click Auto in menu and Unchecked all Boxes.
12. Click Main in menu be sure the Clear Ink Counter and Ink Absorber Counter is set to Main.
13. Click the Counter Value set to 0 and then Click the set button.
13. Then Turn Off the printer.
14. Turn On the printer and it back to normal again and you can now start printing.
 


Thank you...